Closed Loop Servo Driver and Motor Bundle

Closed Loop Servo Driver and Motor Bundle

1 738,13 kr

-10%

1 931,25 kr

Pack description

Closed Loop Servo Driver and Motor Bundle

Newer loose a step again!

When compared with stepper systems, Closed Loop or Hybrid Stepper Servo Drive can close the position loop to eliminate "Loss of Steps". An encoder on the stepper counts the steps made and the signal is feed back to the driver that then compensates if necessary. Even if you push the stepper out of position it will return to its current position. This type of drivers is characterized by having output higher torque, much quick response & acceleration. When compared with brushless servo systems, they have much higher starting and low-speed torque, high standstill stiffness, no overshooting, almost zero settling time, and no tuning for almost for all applications – at reasonable price!

 

2HSS57 is a two-phase closed loop digital driver. It’s controlled by normal STEP/DIR signals and you can use it instead of or together with normal drivers. In this bundle it comes together with 2,0Nm NEMA 23 Step Servo Motor

Features:

* 6.0A Driver

* 2Nm Stepper, shaft Ø8mm

* No lost steps, High accuracy positioning

* 100% rated output torque

*  Variable current control technology, High current efficiency

* Little vibration, Smooth and reliable moving at low speed

* Accelerate and decelerate control inside, smooth starting or stopping of the motor

* User-defined micro steps

* 118x75.5x34mm; 270g

 

The pack contains:

2HSS57 Driver (1)

57J1880EC-1000 Stepper Motor w 1000 line encoder (1)

Encoder cable, 280cm with DB9 Female in one end and wires for terminal mounting in the other. (1) This cable can be extended as needed

Pack content

Closed Loop Servo Driver 6,0A – Just Motion 2HSS57


Closed Loop Servo Driver 6,0A – Just Motion 2HSS57

 

Newer loose a step again!

When compared with stepper systems, Closed Loop or Hybrid Stepper Servo Drive can close the position loop to eliminate "Loss of Steps". An encoder on the stepper counts the steps made and the signal is feed back to the driver that then compensates if necessary. Even if you push the stepper out of position it will return to its current position. This type of drivers is characterized by having output higher torque, much quick response & acceleration. When compared with brushless servo systems, they have much higher starting and low-speed torque, high standstill stiffness, no overshooting, almost zero settling time, and no tuning for almost for all applications – at reasonable price!

 

2HSS57 is a two-phase closed loop digital driver. It’s controlled by normal STEP/DIR signals and you can use it instead of or together with normal drivers. Use together with 2,0Nm NEMA 23 Step Servo Motor

Features:

* No lost steps, High accuracy positioning

* 100% rated output torque

*  Variable current control technology, High current efficiency

* Little vibration, Smooth and reliable moving at low speed

* Accelerate and decelerate control inside, smooth starting or stopping of the motor

* User-defined micro steps

* 118x75.5x34mm; 270g

 

The pack contains:

2HSS57 Driver (1)

Encoder cable, ca. 280cm ø6MM with DB9 Female in one end and wires for terminal mounting in the other. (1) This cable can be extended as needed.

 

Electrical Specifications

Parameters

Min 

Typical 

Max 

Unit 

Supply voltage 

24V

36V

60V

VDC

Output Current (Peak)

-

-

6.0

Amps  

Logic Input Current

-

10 

mA 

Pulse input frequency 

-

200 

KHz 

Low Level Time

2.5

-

-

µsec

 

 

Microstep Resolution Setting

Step / Rev.

SW3

SW4

SW5

SW6

Default

ON

ON

ON

ON

800

OFF

ON

ON

ON

1600

ON

OFF

ON

ON

3200

OFF

OFF

ON

ON

6400

ON

ON

OFF

ON

12800

OFF

ON

OFF

ON

25600

ON

OFF

OFF

ON

51200

OFF

OFF

OFF

ON

1000

ON

ON

ON

OFF

2000

OFF

ON

ON

OFF

4000

ON

OFF

ON

OFF

5000

OFF

OFF

ON

OFF

8000

ON

ON

OFF

OFF

10000

OFF

ON

OFF

OFF

20000

ON

OFF

OFF

OFF

40000

OFF

OFF

OFF

OFF

 

 

 

ALM signal output ports

Port

Symbol

Name

Remark

1

ALM+

Alarm output +

2

ALM-

Alarm output -

 

 

 

Control signal input port

Port

Symbol

Name

Remark

1

PLS+

Pulse signal +

High level 4~5V

2

PLS-

Pulse signal -

Low level 0~0.5V

3

DIR+

Direction signal+

High level 4~5V

4

DIR-

Direction signal-

Low level 0~0.5V

5

ENA+

Enable signal +

High level 4~5V

6

ENA-

Enable signal -

Low level 0~0.5V

 

 

 Power Interface Ports

Port

Identification

Symbol

Name

Remark

1

 

Motor  Phase Wire Input Ports

A+

Phase A+Red

Motor Phase A

2

A-

Phase A- (Blue

3

B+

Phase B+Green

Motor Phase B

4

B-

Phase B-Black

5

 

Power Input Ports

VCC

Input Power +

 

24-50VDC

6

GND

Input Power-

 

NEMA 23 Step Servo Motor – 2Nm – 8mm shaft


NEMA 23 Step Servo Motor – 2Nm – 8mm shaft - 1000 line encoder

Newer loose a step again!

When compared with stepper systems, Closed Loop or Hybrid Stepper Servo Drive can close the position loop to eliminate "Loss of Steps". An encoder on the stepper counts the steps made and the signal is feed back to the driver that then compensates if necessary. Even if you push the stepper out of position it will return to its current position. This type of drivers is characterized by having output higher torque, much quick response & acceleration. When compared with brushless servo systems, they have much higher starting and low-speed torque, high standstill stiffness, no overshooting, almost zero settling time, and no tuning for almost for all applications – at reasonable price!

57J1880EC-1000 is a two-phase Step Servo Motor. It fit all NEMA 23 applications including the Stainless OX. The motor has a 1000-line encoder attached to the end of the motor case. From the motor, you have two wires connection to the driver. One is the 4-connector stepper motor, the other is a 6-connector encoder signal. The later connects via a DB9 Male connector.

This Servo Stepper goes well along with 2HSS57 Closed Loop Servo Driver. 2HSS57 is a two-phase closed loop digital driver. It’s controlled by normal STEP/DIR signals and you can use it instead of or together with normal drivers.

  

Features:

  • Full closed loop
  • Low heat/high efficiency
  • Smooth and accurate
  • High torque /high speed
  • Stepper cable: 50cm, Ø6mm
  • Encoder cable: 20cm, Ø6mm

 

2 phase hybrid step motor Electrical Specification


         Model


Step angle
     (deg)


Holding
torque
  ( N.m)


Current/
 phase
    (A)


Resistance
phase(ohms)


inductance/
phase(mH)


 Detent
 torque
  (gcm)


Rotor inetria
     (g-cm²)


Insulation
    class


lead wire
numbers


Weight
 (kg)


Length
(mm)

57J1880EC-1000

1.8

2.0

5.0

0.36

1.74

700

480

B

4

1.1

105