Extra Large 4 Axis PoKeys Bundle - 2.2Nm

Extra Large 4 Axis PoKeys Bundle - 2.2Nm


1 059,13 kr

-7.5%

1 145,00 kr

In Stock


x 4


1 961,00 kr

-7.5%

2 120,00 kr

In Stock


x 4


2 044,25 kr

-7.5%

2 210,00 kr

In Stock



34,69 kr

-7.5%

37,50 kr

In stock



346,88 kr

-7.5%

375,00 kr

In Stock



78,63 kr

-7.5%

85,00 kr

In stock



57,81 kr

-7.5%

62,50 kr

In Stock


5 582,38 kr

-7.5%

6 035,00 kr

Pack description

Extra Large 4 Axis PoKeys Bundle - 2.2Nm

This Bundle holds the Key Elements you need to setup a CNC Motion Controller for a large and extra large 4 axis machine. Recommended for 1000x1500 and 1500x1500 but can also be used for smaller that need high torque.

To finish up a complete system you also need to add limit switches, wiresconnectors and an enclosure. The system can be further expanded by adding Pendant, Keyboard, an E-Stop with enclosure and more.

This Bundle has the following parts:

PoKeys57CNC (1)

PoStep60 (4)

Just Motion NEMA23 2.2Nm (4)

PoKeys 4 Pin E-Stop Connector w Ribbon Cable (1)

PSU 48V 10A (1)

PSU 12V 2A(1)

E-Stop for Panel Mounting (1)

Pack content

CNC Controller PoKeys57CNC - USB and Ethernet


CNC Controller PoKeys57CNC USB and Ethernet with Mach3 and Mach4 Plugin.

Dump the need for the old school Parallel Port - Connect your CNC to the PC via USB or Ethernet!

PoKeys57CNC is a general purpose motor controller capable of streaming your G-Code from your PC via USB or Ethernet to your CNC machine. The controller supports both Mach3 and Mach4 via Plugins.

The device is able to controlling up to 8 STEP/DIR signal driven motors (stepper motors, servo drives, etc.)

The controller has dedicated, on board, connectors for connection of upto 8 motor drivers, pendants, (HD44780-compatible) LCD module, etc. In addition, 5 analog inputs with 12-bit resolution are available. The device also features four galvanically-isolated open-collector outputs and isolated 0 to 10 V analog output.

A dedicated PoExtBus/PoNET connector can be used to extend the number of digital outputs for additional 80 outputs in the form of either relay outputs or open-collector outputs. It can also be used to connect various additional peripherals e.g. the dust tight CNC keyboard PoKeysKBD48CNC.

For most resent version of the Plugin click here under the "Related Downloads" tab.

Features:

  • Supported by Mach4 and Mach4 plugins
  • Compatible with USB 1.1/2.0 HID standard,
  • standard English USB keyboard simulation (with triggering support for up/down keys),
  • standard USB joystick simulation (6 axes, 32 buttons with triggering support),
  • Ethernet 10/100 with DHCP client or fixed IP support,
  • TCP or UDP connection with the device,
  • Modbus TCP support (access to digital IO, analog inputs, encoder values, digital counters values, PWM outputs, LCD display, PoExtBus devices, matrix keyboard status),
  • web interface with newly designed dashboard and I/O status display with multiple user accounts,
  • 28 digital inputs or outputs (software configurable) with pull-up resistors and available as virtual USB keyboard keys. There are additional 4 dedicated digital outputs,
  • 5 analog inputs (12-bit) with digital low-pass filtering (4 analog inputs also include analog low-pass filter with 1.9 kHz cut-off frequency),
  • multiple encoder pair inputs with three additional dedicated high-speed encoder and one ultra high-speed encoder inputs,
  • digital counters on specific digital input pins,
  • high performance 8-axis 125 kHz pulse engine with dedicated motor connectors,
  • up to 16×8 matrix keyboard with triggered keys/alternate function support,
  • up to 5 high-speed fully configurable PWM outputs (25MHz PWM timer) – two of them with open-collector transistor outputs,
  • Dedicated connector for HD44780-based character LCD support (up to 4×20 characters),
  • Dedicated connector for PoPendant1
  • PoExtBus support for adding up to 10 external shift registers (e.g. PoExtBusOC16, PoExtBusRE, etc.),
  • PoNET devices support (48-key CNC keyboard),
  • fail-safe support in case of communication interruption,
  • support for up to 100 sensors, that can be connected to I2C bus, 1-wire bus or on the general purpose analog inputs,
  • intuitive and user-friendly software,
  • third-party support via communication DLL library and extensive protocol specification document that allows porting to other systems.

Requirements:

  • Ethernet or USB connection between host computer and PoKeys57CNC device
  • 5V DC power supply with 400 mA. If any additional peripheral is connected to PoKeys57CNC, use appropriately more powerful power supply.
  • Included software requires Windows 2000/XP/Vista/Windows 7/8/10 with .NET framework 3.5 installed

Stepper Driver 6,0A - PoStep60-256


Stepper Driver 6,0A - PoStep60-256

Use this high power stepper driver together with any size NEMA 23 or even bigger motors with load up to 6,0A. Connects directly to PoKey57CNC and PoExtBusOC16CNC via 10pin Motor Connector - or to any other STEP/DIR source such as Parallel Port Break out Board or other Motion Controllers. All configuration is done from PC connected via USB

up to 6.0 Amps Phase Current

  • Simple current, microstep and other settings with software via USB
  • Compatible with 4, 6, and 8 wire stepper motors of any voltage
  • +10 VDC to +50 VDC Power Supply
  • 1, 2, 4, 8, 16, 32, 64, 128 and 256 Micro-steps per Step
  • Mixed decay mode for smoother moving of motors
  • 3,3V and 5V logic compatible isolated inputs
  • 250 KHz Max Step Rate
  • 0 °C To 70 °C Operating Temperature
  • LED Power, VM, Status, Fault and Stal indicator
  • On board temperature sensor
  • Improved thermal managing
  • It can be driven from USB without controller
  • Small Size: 54 mm X 75 mm x ca. 20mm

NEMA 23 - 2.2Nm - 8mm shaft


NEMA 23 - 2.2Nm - 8mm shaft

Just Motion branded quality Stepper Motor 57J1880-450

8mm shaft with a flat side for better fixing the Pulley

4 wire connection

1.8deg/step

Phase 2
Torque 2.2N.m
Current 5A
Driver 2DM542, 2DM556 or PoStep60
Weight 1.15kg
Length 80mm

PoKeys 4 Pin E-Stop Connector w Ribbon Cable


PoKeys 4 Pin E-Stop Connector w Ribbon Cable

If you do not need the many connectors and Ribbon Cable that is included in the PoKeys Cable Pac you here get the special connector for the E-Stop and 50cm Ribbon Cable to go with it. To assemble split 4 wires from the 10 wire cable. Press the connector on to the wire using even pressure. Connect E-Stop NC to the two middle wires.

Use only in combination with PoKeys57CNC

Included:

4Pin PoKeys E-Stop connector (1)

10Pin Ribbon Cable (½m)

Power Supply - 48V 10A


Power Supply - 48V 10A

Input: 110/220V AC

Output 3 screw terminals for plus and minus each

Chinese no-name power supply.

Dimensions: 115x50x215

E-Stop for Panel Mounting


E-Stop button for Panel mounting. The button will latch in the down position and it must be rotated to release. The button has two separate contact blocks with a normally open contact set and a normally closed set.

  • Panel Cutout Diameter: 22mm
  • Max Panel thickness 5mm with shim and 7mm w/o shim
  • Depth Behind Panel: 45mm
  • Button Diameter: 40mm

Power Supply - 12V 2A


Micro size Power Supply - 12V 2A

Input: 110/220V AC

Output 1 screw terminal for plus and minus each

Chinese no-name power supply.

Dimensions:  ~(L)8.5 x (W)5.8 x (H)3.8cm