Medium 4 Axis PoKeys Bundle - 0.9Nm/1.3Nm

Medium 4 Axis PoKeys Bundle - 0.9Nm/1.3Nm

1 062,81 kr


1 118,75 kr

In Stock

x 4

627,00 kr


660,00 kr

In Stock

472,63 kr


497,50 kr

In Stock

171,00 kr


180,00 kr

In Stock

173,38 kr


182,50 kr

In Stock

29,93 kr


31,50 kr

In Stock

80,75 kr


85,00 kr

In stock

x 3

1 070,18 kr


1 126,50 kr

In Stock

3 687,66 kr


3 881,75 kr

Pack description

Medium 4 Axis PoKeys Bundle - 0.9Nm/1.3Nm

This Bundle holds the Key Elements you need to setup a CNC Motion Controller for a medium size 4 axis machine. Recommended for 500x750.

To finish up a complete system you also need to add limit switches, wiresconnectors and an enclosure. The system can be further expanded by adding Pendant, Keyboard, an E-Stop with enclosure and more.

This Bundle has the following parts:



Just Motion NEMA23 0.9Nm (3) for Y (2) and Z (1) 

Just Motion NEMA23 1.3Nm (1) for X

PoKeys Cable Pac (1)

PSU 24V 10A

DC-DC Step Down Module

E-Stop for Panel Mounting

Pack content

CNC Controller PoKeys57CNC - USB and Ethernet

CNC Controller PoKeys57CNC USB and Ethernet with Mach3 and Mach4 Plugin.

Dump the need for the old school Parallel Port - Connect your CNC to the PC via USB or Ethernet!

PoKeys57CNC is a general purpose motor controller capable of streaming your G-Code from your PC via USB or Ethernet to your CNC machine. The controller supports both Mach3 and Mach4 via Plugins.

The device is able to controlling up to 8 STEP/DIR signal driven motors (stepper motors, servo drives, etc.)

The controller has dedicated, on board, connectors for connection of upto 8 motor drivers, pendants, (HD44780-compatible) LCD module, etc. In addition, 5 analog inputs with 12-bit resolution are available. The device also features four galvanically-isolated open-collector outputs and isolated 0 to 10 V analog output.

A dedicated PoExtBus/PoNET connector can be used to extend the number of digital outputs for additional 80 outputs in the form of either relay outputs or open-collector outputs. It can also be used to connect various additional peripherals e.g. the dust tight CNC keyboard PoKeysKBD48CNC.

For most resent version of the Plugin click here under the "Related Downloads" tab.


  • Supported by Mach4 and Mach4 plugins
  • Compatible with USB 1.1/2.0 HID standard,
  • standard English USB keyboard simulation (with triggering support for up/down keys),
  • standard USB joystick simulation (6 axes, 32 buttons with triggering support),
  • Ethernet 10/100 with DHCP client or fixed IP support,
  • TCP or UDP connection with the device,
  • Modbus TCP support (access to digital IO, analog inputs, encoder values, digital counters values, PWM outputs, LCD display, PoExtBus devices, matrix keyboard status),
  • web interface with newly designed dashboard and I/O status display with multiple user accounts,
  • 28 digital inputs or outputs (software configurable) with pull-up resistors and available as virtual USB keyboard keys. There are additional 4 dedicated digital outputs,
  • 5 analog inputs (12-bit) with digital low-pass filtering (4 analog inputs also include analog low-pass filter with 1.9 kHz cut-off frequency),
  • multiple encoder pair inputs with three additional dedicated high-speed encoder and one ultra high-speed encoder inputs,
  • digital counters on specific digital input pins,
  • high performance 8-axis 125 kHz pulse engine with dedicated motor connectors,
  • up to 16×8 matrix keyboard with triggered keys/alternate function support,
  • up to 5 high-speed fully configurable PWM outputs (25MHz PWM timer) – two of them with open-collector transistor outputs,
  • Dedicated connector for HD44780-based character LCD support (up to 4×20 characters),
  • Dedicated connector for PoPendant1
  • PoExtBus support for adding up to 10 external shift registers (e.g. PoExtBusOC16, PoExtBusRE, etc.),
  • PoNET devices support (48-key CNC keyboard),
  • fail-safe support in case of communication interruption,
  • support for up to 100 sensors, that can be connected to I2C bus, 1-wire bus or on the general purpose analog inputs,
  • intuitive and user-friendly software,
  • third-party support via communication DLL library and extensive protocol specification document that allows porting to other systems.


  • Ethernet or USB connection between host computer and PoKeys57CNC device
  • 5V DC power supply with 400 mA. If any additional peripheral is connected to PoKeys57CNC, use appropriately more powerful power supply.
  • Included software requires Windows 2000/XP/Vista/Windows 7/8/10 with .NET framework 3.5 installed

Stepper Driver 2.5A - PoStep25-32

Stepper Driver 2.5A - PoStep25-32

Use this small stepper driver together with NEMA17 and smaller NEMA 23 motors with load up to 2,5A. Connects directly to PoKey57CNC and PoExtBusOC16CNC via 10pin Motor Connector - or to any other STEP/DIR source such as Parallel Port Break out Board or other Motion Controllers 

0.5 to 2.5 Amps Phase Current

  • Simple current setting with jumper
  • Compatible with 4, 6, and 8 wire stepper motors of any voltage
  • +10 VDC to +30 VDC Power Supply
  • 1, 2, 4, 8, 16 and 32 Micro-steps per Step - set by DIP switch
  • 0.5 to 2.5A in 0.5A increments - set by jumper
  • Mixed decay mode for smoother moving of motors
  • 3,3V and 5V logic compatible inputs
  • 250 KHz Max Step Rate
  • 0 °C To 70 °C Operating Temperature
  • LED Power, Error and Enable Indicator
  • Improved thermal managing
  • Small Size: 50 mm X 52 mm

NEMA 23 - 1.3Nm - 1/4" shaft

NEMA 23 - 1.3Nm - 1/4" shaft

Just Motion branded quality Stepper Motor 57J1876-828

1/4" shaft with a flat side for better fixing the Pulley

8 wire connection allow series, parallel and Uni-polar Connection


Phase 2
Torque 1.3N.m
Current 2.8A
Driver 2DM542, 2DM556 or PoStep60
Weight 1.0kg
Length 76mm

PoKeys Cable Pac

PoKeys Cable Pac

A good selection of connectors and flat cable - plenty to make a fully loaded control box.

Package includes:

  • 1x flat cable 10pin, length=2m
  • 1x flat cable 20pin, length=40cm
  • 1x flat cable 16pin, length=40cm
  • 1x flat cable 26pin, length=30cm
  • 1x IDC female connector 26 pin
  • 1x IDC female connector 16 pin
  • 1x IDC female connector 20 pin
  • 16x IDC female connector 10 pin
  • 10x poExtension connectors
  • 1x eStop connector
  • 1x SubD25 female connector for flat cable

Photo doesn’t show all connectors and cables.

Power Supply - 24V 10A

Power Supply - 24V 10A

Input: 110/220V AC

Output 2 screw termanalt for plus and minus each

Chinese no-name power supply.

Dimensions: 98x42x199

Voltage Step Down Module

DC-DC Voltage Step Down Module.

Use this module to get a lower voltage from a high voltage Power Supply. Can be very useful in a CNC control box if you need 5V DC for a controller and you only have e.g. a 36V PSU.

Solder on the wires for input/output.


Input voltage: 3-36V

Output voltage: 1.5-35V(Adjustable and must always be somewhat lower than input)

Output current: Rated current is 2A, maximum 3A(Additional heatsink is required)



E-Stop for Panel Mounting

E-Stop button for Panel mounting. The button will latch in the down position and it must be rotated to release. The button has two separate contact blocks with a normally open contact set and a normally closed set.

  • Panel Cutout Diameter: 22mm
  • Max Panel thickness 5mm with shim and 7mm w/o shim
  • Depth Behind Panel: 45mm
  • Button Diameter: 40mm

NEMA 23 - 0.9Nm - 1/4" shaft

NEMA 23 - 0.9Nm - 1/4" shaft

Just Motion branded quality Stepper Motor 57J1854-828

1/4" shaft with a flat side for better fixing the Pulley

8 wire connection


Wiring for "High torque" use a SERIES connection (recommended).

The A coil:

Join YELLOW wire to RED wire

This gives you the two wires for the A coil which you connect to your driver;


The B coil;
Join BLACK wire to ORANGE wire.
This gives you the two wires for the B coil which you connect to your driver.

If you decide to use the "High Speed" wiring then use PARALLEL connection
This results in;

This results in;

Phase 2
Torque 0.9N.m
Current 2.8A
Driver 2DM542, 2DM556, PoStep25 or PoStep60
Weight 0.6kg
Length 54mm